Taskalfa 5500i error code 4101. Also check for continuity within the connector cable.
Taskalfa 5500i error code 4101 Data setup failure. Remedy: Coin jam in the change tube Check visually and remedy. Remedy: Replace the power source PWB and check for correct operation. Engine PWB. After developer motor is stabilized, the ready signal is at the H level for 5 s continuously. Defective fuser heater. Code: 6220 Description: Abnormally high fuser thermistor 2 temperature Fuser thermistor 2 detects a temperature higher than 250°C/482°F for 1 s. Defective connector cable or poor contact in the Code: 7210 Description: Short-circuited outer temperature sensor The sensor input sampling is less than 69. Code: 6020 Description: Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. Also check for continuity within the connector cable. Defective developer thermistor. Remedy: PD PWB K (LSU) 1. Shorted fuser thermistor 2. Code: 6030 Description: Broken fuser thermistor 2 wire A temperature of less than 30°C/86°F was observed at the fuser thermistor 2 when the temperature at the fuser thermistor 1 is greater than 70°C/158°F during warming up. Broken fuser thermistor 2 wire. Code: 6250 Description: Abnormally low fuser thermistor 2 temperature Fuser thermistor 2 detects a temperature lower than 50°C/ 122°F for 1 s after warming up. Code: 4201 Description: BD steady-state error The BD signal is not detected. Causes: PD PWB K (LSU). Code: 2810 Description: Inner motor error Initialized when an error is constantly observed for 2 seconds after the inner motor is activated. Code: 4101 Description: BD initialization error After polygon motor is driven, ASIC detects a BD error for 1 s. This Operation Guide is intended to help you operate the machine correctly, perform routine maintenance and take a simple troubleshooting action as necessary, so that you can always use the machine in good condition. Defective fuser thermistor 2. Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Code: 0640 Description: Hard disk error The hard disk cannot be accessed. TASKalfa 5500i all in one printer pdf manual download. Code: 9080 Description: LED fault detection When the power supply is turned on, the peak value of LED is 80hex or less. Replace the fuser unit. Fuser thermostat triggered. If none, replace Description: Backup memory read/write error (engine PWB) No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively. Jam Codes: 4001 - 4109 *: Refer to figure for paper misfeed indication Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i May 17, 2022 · Kyocera TASKalfa 5500i Error Code 4001 - Taskalfa 5500i dirty copy on drum unit - #jam4001 #jam7901 May 17, 2022 · Kyocera TASKalfa 5500i Error Code 4001 - Taskalfa 5500i dirty copy on drum unit - #jam4001 #jam7901 Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Kyocera TASKalfa 5500i Error Codes List page 5 All About this machine Error Code: All codes Used for the following models 3 Kyocera TASKalfa 3501i Kyocera TASKalfa 4501i Kyocera TASKalfa 5501i Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Kyocera TASKalfa 5500i Error Codes List page 1 All About this machine Error Code: page Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Dec 8, 2024 · Hi viewer in this video i will teach you how to clear error code c3800 in taskalfa 5500i taskalfa 5501i If you have any problem contact me on whatsapp +92307 Sep 21, 2024 · #NewDayUpdates#Nadra#Domocile#TechnicalPrinterIssue#CNIC-NewUpdates#MarriageCertificate-Procedure#Nikahnama#nadraForum-B#StampPapaer#errorcode#paperjamcode#p Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Kyocera TASKalfa 5500i Error Codes List page 4 All About this machine Error Code: page. Error Codes _ Kyocera-Mita _ TASKalfa 5500i _ Code 4101. Used for the following models 3 Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Code: 7460 Description: Developer shutter error Power is turned on while the developer shutter is locked. If it doesn't help, you will need to replace it. Remedy: Shorted fuser thermistor 2. This error is detected 5 times successively. Code: 8300 Description: Center-folding unit communication error Communication with the center-folding unit is not possible. Remedy: Defective hard disk. Defective connector cable or poor contact in the connector. Code 4101 - LSU Defective connector cable or poor contact in the connectormore View and Download Kyocera TASKalfa 5500i operation manual online. Also for: Taskalfa 3500i, Taskalfa 4500i. If none, replace Code: 5101 Description: Main high-voltage error Abnormality of charger roller is detected when Vpp adjustment. Sep 8, 2017 · Re: Taskalfa 5500i Error Code C7101 Make sure that the developer unit is properly locked in place. By following this simple guide, you'll be able to fix your Kyocera TASKalfa printer. Code: 5101 Description: Main high-voltage error Abnormality of charger roller is detected when Vpp adjustment. Jan 30, 2021 · 5500i kyocera Paper Jam 4109 | Paper Jam 15 | kyocera 5500i error codes 4109 | Paper Fail New Video New Day Updates 1. Causes: The battery is disconnected from the main PWB Defective main PWB. Reinsert the connector. Causes: The developer shutter has been locked. Remedy: Contact the Service Administrative Division. Mismatch of reading data from two locations occurs 8 times successively. Defective DF side registration motor 1. Code: 7810 Description: Short-circuited outer temperature sensor The sensor input sampling is less than 0. Defective PD PWB. Defective outer temperature sensor. Defective BDPWB. Defective APCPWB. Defective coin vender control PWB. and keep it close to the machine for easy refe About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features NFL Sunday Ticket © 2025 Google LLC Manuals and User Guides for Kyocera TASKalfa 5500i Mono Laser Printer. Error Code 4101 am experiencing some problems, I do a full fill backup and the next day i want to do a differential backup when i start to write the files i get code 4101. Remedy: The battery is disconnected from the main PWB. Code: 8100 Description: DF eject release motor error When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s. Defective ISC PWB. How To Fix Kyocera TASKalfa Error C0640 || KYOCERA Hard Drive ERROR CODE c0640 c0660 c0670 c0870 THE COPIER WORLD 2. Code: 7901 Description: Drum EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Code: 4101 Description: BD initialization error K After Polygon motor is driven, the BD signal is not detected for 1 s. Code: 2101 Description: Developer motor error After developer motor is driven, the ready signal does not turn to L within 5 s. Code: F278 Description: Power supply in drive system error Causes: Main power switch was turned off without using the power key, or a power failure has occurred C6610 error Kyocera Taskalfa 3501i 4501i 5501i | Step by Step Solutions | Cleaning Solution/s: Fuser release sensor errormore Code: 0980 Description: 24 V power down detect 24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected. Replace the main PWB and check for correct Code: 6200 Description: Broken fuser edge heater wire A temperature of less than 90°C/194 °F was observed at the fuser thermistor when the temperature at the fuser thermistor 1 reached 160°C/ 320 °F after warming up. Code: 4001 Description: Polygon motor synchronization error After polygon motor is driven, the ready signal does not turn to L within 30 s. Defective main PWB. Check the connection the signal cable for CIS and the main PWB, and the continuity across the connector Code: 7210 Description: Short-circuited outer temperature sensor The sensor input sampling is less than 69. Code: 8170 Description: DF side registration motor 1 error 1 When initial operation, DF side registration sensor 1 does not turn on within 3 s. 3500i copier pdf manual download. Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i In this video, we'll show you how to fix Error C4101 and get your printer working properly again. Kyocera TASKalfa 5500i Error Codes List page 6 All About this machine Error Code: All codes Used for the following models 9 Kyocera TASKalfa 2552ci Kyocera TASKalfa 3252ci Kyocera TASKalfa 3552ci Kyocera TASKalfa 4002i Kyocera TASKalfa 4052ci Kyocera TASKalfa 5002i Kyocera TASKalfa 5052ci Kyocera TASKalfa 6002i Kyocera TASKalfa 6052ci In this video, we'll show you How to solve scan to folder error 1102 in Kyocera TASKalfa Printer. Description: Backup memory read/write error (engine PWB) No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively. Defective home position sensor. Code: 8800 Description: Document finisher communication error Communication with the document finisher is not possible. Jam Codes: 4001 - 4109 *: Refer to figure for paper misfeed indication Code: 7301 Description: Toner hopper motor error When the toner hopper motor is driven, toner hopper sensor does not turn on within 200 ms. T/C sensor BK errorCauses:For the specified value of the initial toner stored in the EEPROM of the developer unit, the output value of the T/C sensor is out Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Code: 4101 Description: BD initialization problem (K) BD is not detected within two seconds after the polygon motor stabilizes. If none, replace the cable Code: 3100 Description: Scanner carriage error The home position is not correct when the power is turned on or at the start of copying using the table. Code: 1720 Description: Paper feeder incompatible detection error The paper feeder has been installed with a device to which it is incompatible. If none Code: 4001 Description: Polygon motor synchronization error After polygon motor is driven, the ready signal does not turn to L within 30 s. Defective drive transmission system of motor. Defective connector cable or poor contact in the connector (1000-sheet finisher) Defective DF side registration sensor 1. Kyocera TASKalfa 5500i PCL Barcode Flash 3. Defective high voltage PWB Defective engine PWB. Causes: Poor contact in the connector terminals. Mismatch between writing data and reading data occurs 8 times successively. Reinsert the Code: 2550 Description: Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. If none, replace the Code: 0630 Description: DMA error DMA transmission of image data does not complete within the specified period of time. Remedy: Contact the Service Code: 4101 Description: BD initialization error K After Polygon motor is driven, the BD signal is not detected for 1 s. Code: 6200 Description: Broken fuser edge heater wire A temperature of less than 90°C/194 °F was observed at the fuser thermistor when the temperature at the fuser thermistor 1 reached 160°C/ 320 °F after warming up. If none, replace the Code: 3500 Description: Communication error between scanner and ASIC An error code is detected. BONUS: We show you the secret Jam area and how to reduce moisture in your printer paper. Defective fuser front fan motor. Description: Inner motor error Initialized when an error is constantly observed for 2 seconds after the inner motor is activated. Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Kyocera TASKalfa 5500i Error Codes List page 7 All About this machine Error Code: page Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Troubleshooting. Replace the engine PWB and check for correct operation. 62K subscribers Subscribe Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i How to Clear Error C5101 Koycera Taskalfa 5501i ||5500i Full Video Watch Usama Technical 406 subscribers Subscribe Code: 0160 Description: Backup memory data error (engine PWB) Reading data from EEPROM is abnormal. Defective engine PWB. Used for the following models 9 Kyocera TASKalfa 2552ci Kyocera TASKalfa 3252ci Kyocera TASKalfa 3552ci Kyocera TASKalfa 4002i Kyocera TASKalfa 4052ci Kyocera TASKalfa 5002i Kyocera TASKalfa 5052ci Kyocera TASKalfa 6002i Kyocera TASKalfa 6052ci Code: 6900 Description: Fuser front fan motor error When the fuser front fan motor is driven, alarm signal is detected for 5 s continuously. Code: 0180 Description: Machine number mismatch Machine number of main and engine does not match. Poor contact in Code: 7810 Description: Short-circuited outer temperature sensor The sensor input sampling is less than 0. Defective PWB. Defective scanner motor. Shorted fuser thermistor 1. Defective polygon motor. Replace the coin mec. Defective CIS Defective DPSHD PWB. We'll provide you wit Code: 4001 Description: Polygon motor synchronization error After polygon motor is driven, the ready signal does not turn to L within 30 s. Deformed connector pin. Code: 7241 Description: Broken developer thermistor wire The sensor input sampling is greater than 230. Code: 9150 Description: Sensor error in coin vender change (Yen 500) Change is empty despite change is enough. Code: 0980 Description: 24 V power down detect 24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected. An error is constantly observed for 2. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. If none, replace Code: 6900 Description: Fuser front fan motor error When the fuser front fan motor is driven, alarm signal is detected for 5 s continuously. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. If none Code: 7241 Description: Broken developer thermistor wire The sensor input sampling is greater than 230. Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Code: 7210 Description: Short-circuited outer temperature sensor The sensor input sampling is less than 69. Remedy: Poor contact in the connector terminals. Causes: The paper Description: The fuser pressure release error The fuser release sensor does not turn on or off, after 30 s from starting pressurization or depressurization operation. Defective exposure lamp Defective CCD PWB. 5 seconds after rebooting. Code: 3300 Description: Optical system (AGC) error After AGC, correct input is not obtained at CCD. keep getting an error 4101 at step three when the installer asks for me to turn on airplane mode. 9K subscribers Subscribe Description: Backup memory read/write error (engine PWB) No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively. Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Error Code Service Mode, Troubleshooting Parts Catalog Downloads Files Home Email: Password: Sign In New Register Code: 4101 Description: BD initialization error After polygon motor is driven, ASIC detects a BD error for 1 s. Code: 0840 Description: Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed. Causes: Deformed connector pin. Code: 9010 Description: Coin vender communication error A communication error from coin vender is detected 10 times in succession. Code: 6230 Description: Broken fuser thermistor 2 wire Input from fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s. Causes: Coin jam in the change tube Poor contact in the connector. Causes: Defective hard disk. Replace the Code: 3500 Description: Communication error between scanner and ASIC An error code is detected. Kyocera TASKalfa 55001i Code #6610 | sensor error #ErrorCodes #Kyocera #TASKalfa5501i #Code 6610 New Day Updates 1. Defective connector cable or poor contact in the Code: 4101 Description: BD initialization error After polygon motor is driven, ASIC detects a BD error for 1 s. Used for the following models 3 Code: 7460 Description: Developer shutter error Power is turned on while the developer shutter is locked. Causes: Defective power source PWB. 0_KYOmulticode 1. Troubleshooting. Causes: Data damage of EEPROM. Causes: Defective bottom plate elevation mechanism in the cassette. Error Code Service Mode, Troubleshooting Parts Catalog Downloads Files Home Email: Password: Sign In HOW TO: Find the paper Jam on a #kyocera #taskalfa Multifunction printer. Defective triac. Code: 8180 Description: DF side registration motor 1 error 2 JAM6810 is detected twice. Causes: Defective connector cable or poor contact in the connector. Defective toner hopper sensor. If none, replace the Code: 0980 Description: 24 V power down detect 24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected. 0 Quick Installation Guide Kyocera TASKalfa 5500i PCL Barcode Flash Device Support and KYOmulticode Manual Kyocera TASKalfa 5500i PRESCRIBE Commands Command Reference Manual Kyocera TASKalfa 5500i PRESCRIBE Commands Technical Reference Manual Thank you for your purchase of TASKalfa 3500i/TASKalfa 4500i/TASKalfa 5500i. Used for the following models 3 Kyocera TASKalfa 3501i Kyocera TASKalfa 4501i Kyocera TASKalfa 5501i Code: 4101 Description: BD initialization error After polygon motor is driven, ASIC detects a BD error for 1 s. Also for: 4500i, 5500i, 6500i, 8000i. Reinsert the View and Download TASKalfa 3500i troubleshooting manual online. We have 19 Kyocera TASKalfa 5500i Mono Laser Printer manuals available for free PDF download: Service Manual, Operation Manual, Command Reference Manual, Technical Reference Manual, Driver Manual, User Manual, Specifications, Quick Manual, Safety Manual Kyocera 5500i Code 7301 | Lntermediate Toner Hopper Toner Feed Error C7301 | BlackToner Container kyocera taskalfa 5500i Good Print Result | PCR Charge Roller | #3500i #3501i #4500i #4501i #5500i Code: 4101 Description: BD initialization error After polygon motor is driven, ASIC detects a BD error for 1 s. Remedy: Shorted fuser thermistor 1. Defective Code: 2101 Description: Developer motor error After developer motor is driven, the ready signal does not turn to L within 5 s. Defective CF set sensor. Remedy: Defective connector cable or poor contact in the connector. Remedy: Defective fuser thermistor 2. Release the developer shutter. This error is detected 4 times successively. If none, replace Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Code: 2550 Description: Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. If none, replace Code: 3500 Description: Communication error between scanner and ASIC An error code is detected. Defective connector cable or poor contact in the connector (1000-sheet finisher). Causes: Defective connector cable or poor contact in the connector (4000-sheet finisher). Used for the following models 3 Kyocera TASKalfa 3500i Kyocera TASKalfa 4500i Kyocera TASKalfa 5500i Description: Backup memory read/write error (engine PWB) No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively. The lock signal of the motor is detected continuously for 1 s. Jam Codes: 4001 - 4109 *: Refer to figure for paper misfeed indication Troubleshooting. This error is detected 15 times successively. Defective inner motor. 51K subscribers 52 If you're experiencing problems with your Kyocera TASKalfa printer, be sure to watch this video for tips on how to fix the error C7101. Remedy: The developer shutter has been locked. Find all the documentation, manuals and drivers you could need for your KYOCERA product right here. Code: 1020 Description: Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. Defective change empty sensor. Check visually and remedy if necessary Defective main PWB. vnmz mrvxx vqsi oiymx malui jfxqis qcsf rbdsws bbp zet nsmygg bdvbdti xcl dfpgl ivccz